Camera Not Giving Option to Upload to Computer Apeman A66
In this article, there are v ways you lot can connect your Security IP Photographic camera to your estimator. And nosotros will cover the steps on how you should do information technology without a router, without internet, without a DVR/NVR or without its receiver. The following table summarizes the important information about connecting IP camera to your figurer for your reference.
| Photographic camera types: | POE camera or WiFi camera |
| Bone(functioning system): | Windows or Mac |
| Cable: | 2-in-1 or 3-in-ane cable attached from the camera |
| Remotely access by: | Photographic camera'due south UID |
Annotation: Beginning you should install the security camera in the right place. You tin refer to How to Install Home Security Cameras Successfully.
5 Methods to Connect Your Security IP Camera to PC/Mac：
To go far easier for you to find the correct solution, you tin can click and jump directly to the section you want.
For example, if your photographic camera is a PoE camera, then you tin can cull choice 3 or 4.
- 1. Connect Directly to PC/Mac (without Internet)
- 2. Connect via Router (with Internet)
- iii. PoE (Wired) Camera without Injector/Switch
- iv. PoE (Wired) Camera with Injector/Switch
- 5. Connect a CCTV Photographic camera Organisation to PC/Mac
Of import Notation: The methods recommended below may Non apply for the battery-powered security cameras, which require initial setup on your phones.
Connect a WiFi or PoE Camera Directly to PC/Mac (without Net)
Here'due south how to connect your security IP camera direct to a PC/Mac without an NVR or DVR, without a router network, without WiFi, and without any costs or complicated configurations.
you need to fix the camera's power adapter and a network cable.
1. Get your security photographic camera charged.
Use the power adapter to get the camera plugged-in and charged. Ordinarily, when you buy a WiFi IP photographic camera, it comes with a power adapter. For a PoE camera, ask the supplier and buy 1 that's workable for the photographic camera.
two. Use the network cable to connect to the camera and the computer.
Commonly there would be a 2-in-1 or 3-in-1 cable attached from the photographic camera. Discover the network connector from that cable and use the network cable to connect to information technology. Then connect the other cease of the network cable to the computer. If your reckoner has a network already, disable it – make sure your computer is offline. 
3. Browse and discover out the security camera's IP address on the computer.
Now the security photographic camera is connecting to your computer basically and physically. But you yet tin't view the camera on the computer. What you need to do now is to browse and notice out the photographic camera'south IP address. At that place should be surveillance software from the same supplier with the camera. Have our test as an example. Nosotros take Reolink Customer on the calculator. Launch it and it will automatically scan all the cameras in the aforementioned local LAN and show the default IP address (every camera has a default and unique IP accost when it leaves the factory). Like shooting fish in a barrel peasy! 
4. Change the computer'southward IP accost to the same network prefix of the IP camera.
And so in Step 3, y'all get your security camera'south default IP accost. In our examination, the default IP address of the photographic camera we use is 192.168.177.100, and now you need to modify your figurer's IP address to 192.168.177.x, where x identifies the node/host and is the number between 2 and 254. So let'south say the computer's IP address is 192.168.177.12.
IP accost 101: An IP address consists of two parts – one belongs to the network accost and one belongs to the node address. All nodes on a given network share the same network prefix merely have a unique host number.
Now to change the reckoner'south IP address (we take Windows x as an example):
one) Press the Windows + R keyboard shortcut to bring out the Run box.
2) Enter "ncpa.cpl" and open the "Network Connections" window.
iii) Right-click your computer' network adapter and select "Properties".
4) Select your computer's Internet Protocol Version and click "Backdrop".
5) Select "Apply the following IP address" and alter the IP accost into 192.168.177.12.
And washed. At present your IP camera is connecting directly and communicating with your PC, because they are now in the same petty LAN. You can watch your IP camera with Reolink Client on your reckoner.
Important: Since there is no router network, the IP camera would non transmit data or send alarms to your phone. Still, you can tape and relieve all the footage onto your computer.
If you lot're gonna apply your IP camera with the figurer all the time like this (without router network), you lot'd improve change the default status of your IP camera'southward IP accost to the static to go along it the same all the fourth dimension, considering each time yous reboot the IP photographic camera, its IP address will be changed and you will need to do all the steps above once again. To keep the IP camera'due south IP address the same all the time, caput to "Device Settings" and "Network General" on the Client (Reolink Client in our test), and choose "Static" for "Network Admission". And done. 
Connect a Wireless/WiFi Camera to Computer via Router (with Internet)
If yous do accept WiFi network and need to remotely see the IP camera when you're not there, you can connect your wireless or WiFi camera to computer wirelessly via your router. Please notation that you demand to have, at least, a power adapter for the photographic camera, a network cable, and a router.
1. Go your WiFi security photographic camera charged.
Use the ability adapter to get the photographic camera plugged-in and charged.
2. Apply the network cablevision to connect to the camera and the router.
A WiF camera needs to connect to the router with a network cablevision for initial setup, because the new camera itself wouldn't recognize and auto-option up a network that it never uses. Only after the correct WiFi settings tin you disconnect the cable from the camera and the router. And aye again, normally there would be a 2-in-i or three-in-i cablevision attached from the WiFi camera. Find the network connector from that cable and use the network cablevision to connect to it. Then connect the other terminate of the network cablevision to the router. 
iii. Lookout the IP camera on PC/Mac
On the reckoner, launch the surveillance software to add the camera and watch alive view direct. In our exam, we open Reolink Client. Since the calculator and the camera are in the same network (using the aforementioned router network), Reolink Customer automatically searches and displays the photographic camera directly. Click "Start" and yous tin view the camera on PC. And you tin can set up the configurations for all the functions you want the photographic camera to accept.
4. Set up up WiFi settings and remove the network cable.
Exercise remember to brand the WiFi settings for the camera. On the software, navigate to "Device Settings" and "Network". Choose the WiFi network and enter the password, and done. Cameras from the dissimilar brands would accept dissimilar WiFi settings. Please refer to the guides you go from your supplier. After that, remove the network cablevision, and then the security IP CCTV camera connects to the estimator wirelessly.
Of import: If yous demand to see the IP camera from another calculator that is not in the same network, you lot need to input the camera's UID into the software to remotely admission the camera.
Connect a PoE (Wired) IP Camera to Computer without PoE Injector/Switch
Connecting a PoE wired IP camera to a computer via the router is like to that of a WiFi camera, and even much easier – y'all don't need to use a power adapter, fix the WiFi and remove the network cable. And you need at least one network cable, and a router with PoE capability to complete the setup.
one. Use the network cable to connect to the photographic camera and the router.
PoE (Power over Ethernet) ways you can simply use a unmarried network cable for both video and power transmission. So only connect the photographic camera to the router via the network cable, and the camera will get power supply and network access. 
Please make certain your router has the PoE feature. If not, try the next method.
2. Sentinel the IP camera on the computer.
On the computer, launch the surveillance software to add the camera and lookout alive view directly. In our test, we open Reolink Client. Since the calculator and the camera are in the same network, Reolink Customer automatically searches and displays the camera direct. Click "Offset" and you can view the camera on PC. And yous can set up the configurations for all the functions you want the camera to have.
Important: If you need to run into the IP photographic camera from another computer that is not in the same network, you need to input the camera'southward UID into the software to remotely admission the camera.
Connect a PoE (Wired) IP Photographic camera to Computer with PoE Injector/Switch
If your router does not support PoE, yous need a PoE injector or PoE switch to help connect your IP camera to PC.In society to complete the setup yous need at to the lowest degree a network cablevision, a router, and a PoE injector or PoE switch. Since the steps on how to connect a PoE IP camera to PC via PoE Injector/switch are quite the same to that of connecting without a PoE Injector/switch, nosotros'd like to make it more than simpler to understand here.
1.connect the security camera, router and PoE injector
Connect all the devices every bit the picture showed beneath, brand sure your wireless IP camera is connected to a ability supply. 
2. Open Reolink Client & add together the photographic camera directly
You lot can at present open Reolink Customer on your calculator, add the camera and sentry live view directly. If yous need to see the IP photographic camera from another computer that is non in the aforementioned network, you demand to input the camera'south UID into the software to remotely access the camera.
Important: Once you lot connect the PoE IP camera to the PoE injector or switch which is connected to a router via Ethernet cables, you've successfully connected the photographic camera to the network. For a wireless IP camera, you demand to utilise a network cable to connect it to the router if you oasis't fix the WiFi network configuration. And then the wireless IP photographic camera is in the network. You can fix up the WiFi configuration later on to make the wireless IP camera connect wirelessly.
Connect a CCTV Camera Arrangement to PC/Mac (with or without Network)
If y'all are using a CCTV photographic camera system, similar the Reolink PoE kit RLK8-410B4, instead of single security camera, yous may need the following tutorial. A CCTV photographic camera organization oftentimes have their ain proprietary networks, and can work with and without your router network.
i. How to connect a CCTV security camera organisation to a computer without router network
- Connect all the cameras to the NVR:When you receive the new IP camera organization y'all bought, connect all the devices you lot got – connect the NVR to your reckoner's monitor and the mouse, use the power adapters to accuse the NVR and cameras, etc. For a WiFi system, in one case the WiFi NVR and the WiFi cameras are charged, they connected to each other automatically and would first to communicate. For a PoE system, connect the PoE cameras to the NVR via the network cables provided.
- Kickoff watching the IP cameras:The startup and setup wizard will pop up to guide you to picket your cameras and practise other configurations.
At present y'all can see all the IP cameras on your monitor and start recording.
2. How to connect a CCTV security camera arrangement to a computer with router network
- Do the step ane shown in a higher place again.
- Connect the NVR to your router via the network cable provided.
- Start watching the IP cameras.
The startup and setup wizard will pop up to guide you to watch your cameras and do other configurations. If you demand to see the IP cameras from some other computer that is non in the same network, you demand to input the NVR's UID into the software to remotely admission the cameras.
Inforgraphic:
The infographic below too covers our 5 methods to connect IP security camera to PC/Mac . Promise this can exist helpful to you.
Third-Party Software to Connect IP Camera to PC/Mac
You tin can as well opt for third-party software to connect and gear up up a security camera on the calculator. Make certain the software tin can handle all the cameras on the network and support all the features for the cameras. Normally, the 3rd-party software has several versions. And if you want to use full features of the camera, you lot need to pay for a premium version. If your security IP camera is not working properly as expected or if you lot become any problems, you can try the top 10 solutions to fix IP cameras non working.
For whatever questions, please don't hesitate to exit it in your comment. I will answer as presently equally possible.
Source: https://reolink.com/connect-security-ip-camera-to-pc/
0 Response to "Camera Not Giving Option to Upload to Computer Apeman A66"
Post a Comment